Milwaukee Impact Wrench Bedienungsanleitung PDF herunterladen (Seite 5)

page 5

TOOL ASSEMBLY

WARNING!

Use only sockets and other accessories specifically

designed for use on impact wrenches and drivers.

Other sockets and accessories might shatter or

break causing injury.

Attaching and Removing the Tool Hanger (Fig. 2)

(Cat. No. 9092-20, 9096-20, or as an accessory)

Attaching and Removing Accessories (Fig. 3)

Cat. No. 9071-20, 9075-20

This impact wrench is intended only for use with sockets designed for

impact wrenches and that have a 1/2" square drive (3/4" square drive

for Cat. No. 9075-20). Other sockets could shatter or break, causing injury.

1. To attach a socket or other accessory, push the accessory onto the

drive shank until it snaps into place.

2. To remove the accessory, pull it off the drive shank.

Attaching and Removing Accessories (Fig. 4)

Cat. No. 9070-20, 9072-20

These impact wrenches are intended only for use with sockets designed

for impact wrenches and that have a 1/2" square drive. Other sockets

could shatter or break, causing injury.

1. To attach a socket or other accessory, align the hole in the acces-

sory with the detent pin on the drive shank. Hold the detent pin in

while pushing the socket onto the drive shank. The detent pin will

snap into place in the hole to secure the socket.

2. To remove the accessory, insert a nail or other thin object into the

hole in the accessory and press the detent pin in. Pull the accessory

off the drive shank.

Fig. 3

Drive shank

Fig. 4

Drive shank

Detent pin

Attaching and Removing Accessories (Fig. 5)

Cat. No. 9092-20, 9096-20, or other Impact Wrenches using the

Quick Change 1/2" Square Drive to 7/16" Hex Adapter

Cat. No. 9092-20 and accessory Cat. No. 48-66-0061 are intended for

use with drill bits and adapters with a 7/16" Hex Quick Change shank.

Cat. No. 9096-20 is intended for use with drill bits and adapters with a

5/8" Hex Quick Change shank. Both Hex Quick Change shanks have a

ball-retainer groove. They are not intended for use with Hex Shank Bit

Extensions.

1. To attach, remove the two top gear case screws (Fig. 2).

2. Place the ring through the tool hanger.

3. Position the tool hanger on the tool over the two gear case screw

holes.

4. Replace the two gear case screws. Hand tighten the screws.

5. To remove, reverse the procedure.

Fig. 2

Gear case

screws

Tool

hanger

Ring

WARNING!

To reduce the risk of injury, always unplug

tool before attaching or removing accessories

or making adjustments. Use only specifically

recommended accessories. Others may be

hazardous.

Removing and Replacing Quik-Lok

Cords (Fig. 1)

(Cat. No. 9072-20, 9092-20 and 9096-20)

MILWAUKEE

's exclusive Quik-Lok

Cords provide instant field replace-

ment or substitution.

1. To remove the Quik-Lok

Cord, turn the cord nut 1/4 turn to the left

and pull it out.

2. To replace the Quik-Lok

Cord, align the connector keyways and push

the connector in as far as it will go. Turn the cord nut 1/4 turn to the

right to lock.

1. To attach an accessory, pull the chuck collar forward and insert the

accessory shank. Release the collar. It may be necessary to pull the

bit out slightly to engage the holding mechanism.

2. To remove the accessory, pull the chuck collar forward and remove

the accessory. Release the collar.

Fig. 5

Open (Release)

Closed (Locked)

Ball-retainer

groove

Fig. 1

1 2 3 4 5 6 7 8 9 10 ... 19 20

Kommentare zu diesen Handbüchern

Keine Kommentare

Milwaukee Impact Wrench Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Werkzeug Milwaukee Impact Wrench