Milwaukee 5337-20 Bedienungsanleitung

58-92-5300 d3 REPAIRINSTRUCTIONS032005Cat. No. 5337-203/4” Hex Demolition HammerCat. No. 5340-202” Spline Rotary HammerMILWAUKEE ELECTRIC TOOL CORPORA

10PAGE58-92-5300 d3INSTRUCTIONSREPAIRMaintenanceGeneral It is recommended that maintenance be performed on the machine at regular intervals or when th

11PAGE58-92-5300 d3INSTRUCTIONSREPAIRLubrication: Combined drill/chisel hammer (5340-20) Re

12PAGE58-92-5300 d3INSTRUCTIONSREPAIRLubrication: Chisel hammer (5337-20)

13PAGE58-92-5300 d3INSTRUCTIONSREPAIRSequence and torques of the screws:BACDEFGHIJKLMN

14PAGE58-92-5300 d3INSTRUCTIONSREPAIRAssemblyInstalling the anti-vibration mechanismand field1 Install field (6) into motor housing (8) and secure it

15PAGE58-92-5300 d3INSTRUCTIONSREPAIRInstalling the gear box cover1 Secure gear box cover (2) with two screws (1) onto the gear box (torque = 3 Nm / 2

16PAGE58-92-5300 d3INSTRUCTIONSREPAIRAssembling the armature1 Press bearing (B) onto armature shaft and install bearing cup (C) into rear bearing bore

17PAGE58-92-5300 d3INSTRUCTIONSREPAIRInstalling the motor housing1 Apply Blue loctite® onto four screws (4).Install gear box and armature (5) into mo-

18PAGE58-92-5300 d3INSTRUCTIONSREPAIRAssembling the spindle1 Install washer (E) and the back pressure o-ring (C) into spindle (F).☞Install thrust coll

19PAGE58-92-5300 d3INSTRUCTIONSREPAIRSDS Max combined drill/chisel hammer:To check static slip of clutch1 Secure hammer gear box in a machinists vise.

2PAGE58-92-5300 d3INSTRUCTIONSREPAIRSpecialTools Require– Forcing discs 61-10-0011– Hex key 4 mm– Hex key 5 mm– Sleeve 61-10-0013– Pin-type face spa

20PAGE58-92-5300 d3INSTRUCTIONSREPAIRCombined drill/chisel hammer:Installing the spindle1 Install complete spindle assembly (1) into gear box (2) as f

21PAGE58-92-5300 d3INSTRUCTIONSREPAIRInstalling thetop gear box cov-er1 Install gasket (4) into gear box (6). Mind the right position!☞Gasket (4) is p

22PAGE58-92-5300 d3INSTRUCTIONSREPAIRInstalling thenose piece as-sembly1 Install o-ring (2) and seal ring (3) into the nose piece assembly (1).☞Instal

23PAGE58-92-5300 d3INSTRUCTIONSREPAIR–Installingthe handle1 Press retainers (2) together on both sides and install the handle (4).2 Insert screw (1) i

3PAGE58-92-5300 d3INSTRUCTIONSREPAIRRemoving the spring ring1 Remove both retainers (1).2 Slightly spread spring ring (2) and pull it off the machine

4PAGE58-92-5300 d3INSTRUCTIONSREPAIRCombined drill/chisel hammer:Removingthe spindle1 Drive out the complete spindle assembly with light taps on rear

5PAGE58-92-5300 d3INSTRUCTIONSREPAIRDisassembling the spindle1 Remove thrust collar (1) from spindle (7). Remove O-ring (2) from thrust collar (1).2 D

6PAGE58-92-5300 d3INSTRUCTIONSREPAIRRemoving the piston assembly1 Bring piston (3) into the upper dead center position and remove it from gear. Remove

7PAGE58-92-5300 d3INSTRUCTIONSREPAIRDisassembling the armature1 Remove three hex head screws (8) from bearing end plate (7) and pull complete ar-matur

8PAGE58-92-5300 d3INSTRUCTIONSREPAIRRemoving the gear cover1 Remove two screws (1) and remove gear cover (2).☞The exposed plane surface serves only fo

9PAGE58-92-5300 d3INSTRUCTIONSREPAIRRemoving the anti-vibration mechanismand the field1 Remove air deflector ring (5).2 Remove screw (4). Remove the f